顎式破碎機課程設計
Ⅰ 機械原理課程設計（顎式破碎機）的c語言源程序
我已改正如下：
#include
"stdio.h"
#include
"conio.h"
#include
"math.h"
#define
pi
3.1415926
main()
{
double
c0,c1,c2,c3,c4,c5,c8,c9,l1,l2,l3,l4,l5,l8,l9,w1,w2,w3,w4,w5,a2,a3,a4,a5,A,B,C,D,E,F;
scanf("c1=%lf\n",&c1);//輸入類型也必須格式化為double型，所以用%lf
l1=0.1;
l2=0.4;
l3=0.3;
l4=0.26;
l5=0.6;
l8=0.48;
l9=0.58;
c8=2*pi/3;
c9=2.7053;
w1=3*pi;
A=2*l1*l3*sin(c1)-2*l3*l9*sin(c9);
B=2*l1*l3*cos(c1)-2*l3*l9*cos(c9);
C=l2*l2-l3*l3-l9*l9-l1*l1+2*l1*l9*cos(c1-c9);
c3=2*atan((A-sqrt(A*A+B*B-C*C))/(B-C));
c2=acos((l3*cos(c3)+l9*cos(c9)-l1*cos(c1))/l2);
c0=c2-pi/6;
D=(-2)*l5*l8*sin(c8)+2*l1*l5*sin(c1)+2*l5*l2*sin(c0);
E=(-2)*l5*l8*cos(c8)+2*l1*l5*cos(c1)+2*l5*l2*cos(c0);
F=l4*l4-l5*l5-l8*l8-l1*l1-l2*l2+2*l2*l8*cos(c0-c8)-2*l1*l2*cos(c1-c0)+2*l1*l8*cos(c1-c8);
c5=2*atan((D+sqrt(D*D+E*E-F*F))/(E-F));
c4=acos((l5*cos(c5)+l8*cos(c8)-l1*cos(c1)-l2*cos(c0))/l4);//少個分號，我已加上~
w2=((-w1)*w1*l1*sin(c1-c3))/(l2*sin(c2-c3));
w3=(w1*l1*sin(c1-c2))/(l3*sin(c3-c2));
w4=(l1*w1*sin(c5-c1)+l2*w2*sin(c5-c0))/(l4*sin(c4-c5));
w5=(l1*w1*sin(c1-c4)+l2*w2*sin(c0-c4))/(l5*sin(c5-c4));
a2=((-w1)*w1*l1*cos(c1-c3)-w2*w2*l2*cos(c2-c3)+w3*w3*l3)/(l3*sin(c2-c3));
a3=(w1*w1*l1*cos(c1-c2)+w2*w2*l2-w3*w3*l3*cos(c3-c2))/(l3*sin(c3-c2));
a4=(l5*w5*w5*cos(2*c5)-l1*w1*w1*cos(c5-c0)-l4*w4*w4*cos(c4-c5))/(l4*sin(c4-c5));
a5=(l1*w1*w1*cos(c1-c4)+l2*w2*w2*cos(c4-c0)+l4*w4*w4*cos(2*c4)-l5*w5*w5*cos(c5-c4))/(l5*sin(c5-c4));
printf("c2=%f\n,c3=%f\n,c4=%f\n,c5=%f\n,w2=%f\n,w3=%f\n,w4=%f\n,w5=%f\n,a2=%f\n,a3=%f\n,a4=%f\n,a5=%f\n,A=%f\n,B=%f\n,C=%f\n,D=%f\n,E=%f\n,F=%f\n",c2,c3,c4,c5,w2,w3,w4,w5,a2,a3,a4,a5,A,B,C,D,E,F);
getch();
}
你看看還有什麼問題？
Ⅱ 機械原理課程設計 鉸鏈式顎式破碎機
目錄
一．機構簡介與設計數據·········································3
二．圖解法連桿機構運動分析及動態靜力分析···································································5
三．桿組法顎式破碎機的運動分析及動態靜力分析
·································································11
四．飛輪設計····················································21
五．主要收獲 ···················································22
六．參考文獻 ····················································22
顎式破碎機
一、機構簡介與設計數據
（1）機構簡介
顎式破碎機是一種破碎礦石的機械，如圖所示，機器經皮帶（圖中未畫）使曲柄2順時針回轉，然後通過構件3，4，5是動顎板6向左擺向固定於機架1上的定額板7時，礦石即被軋碎；當動顎板6向右擺定顎板時，被軋碎的礦石即下落。
由於機器在工作過程中載荷變化很大，將影響曲柄和電動機的勻速運轉。為了減小主軸速度的波動和電動機的容量，在O2軸的兩端各裝一個大小和重量完全相同的飛輪，其中一個兼作皮帶輪用。
圖1.1 六桿鉸鏈式破碎機
圖1.2 工藝阻力
（2）設計數據
設計內容
連桿機構的遠動分析
符號
n2
Lo2A
L1
L2
h1
h2
lAB
lO4B
LBC
Lo6c
單位
r/min
mm
數據
170
100
1000
940
850
1000
1250
1000
1150
1960
連桿機構遠動的動態靜力分析
飛輪轉動慣量
的確定
IO6D
G3
JS3
G4
JS4
G5
JS5
G6
JS6
mm
N
Kg m2
N
Kg m2
N
Kg m2
N
Kg m2
Ⅲ 鉸鏈式鄂式破碎機課程設計
錘式破碎機主要是靠沖擊作用來破碎物料的.破碎過程大致是這樣的,物料進入破碎機中,遭受到高速回轉的錘頭的沖擊而破碎,破碎了的物料,從錘頭處獲得動能,從高速沖向架體內擋板,篩條,與此同時物料相互撞擊,遭到多次破碎,小於篩條之間隙的物料,從間隙中排出,個別較大的物料,在篩條上再次經錘頭的沖擊,研磨,擠壓而破碎,物料被錘頭從間隙中擠出.從而獲得所需粒度的產品.